{"product_id":"quick-mill-flow-control-lever-wood","title":"Flow Control Device (Wood)","description":"\u003cmeta charset=\"utf-8\"\u003e\n\u003ch3 data-mce-fragment=\"1\"\u003e\n\u003cb data-mce-fragment=\"1\"\u003ePlease Read\u003c\/b\u003e\u003cbr data-mce-fragment=\"1\"\u003e\n\u003c\/h3\u003e\n\u003cp data-mce-fragment=\"1\"\u003eWARNING! Please note that we are not responsible for any damage before, during, or after installation. Damages can include, but not limited to:\u003c\/p\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003eOver-tightening the gauge into the group head (causing the gauge thread to break and threading broken inside the group head). Replacement\u003cspan data-mce-fragment=\"1\"\u003e \u003c\/span\u003e\u003cspan style=\"text-decoration: underline;\"\u003e\u003ca data-mce-fragment=\"1\" title=\"flow control gauge\" href=\"https:\/\/www.chriscoffee.mom\/products\/qm-flow-control-gauge-6x8mm\" target=\"_blank\" data-mce-href=\"https:\/\/www.chriscoffee.mom\/products\/qm-flow-control-gauge-6x8mm\"\u003eLinked here\u003c\/a\u003e\u003c\/span\u003e\u003cspan data-mce-fragment=\"1\"\u003e.\u003c\/span\u003e\n\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003eBreaking of gaskets and o-rings,\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003eScratches on mushroom,\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003eOver-tightening of gicleur, and\/or\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003eLimescale build up.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp data-mce-fragment=\"1\"\u003eIf your machine has an E61 group head, YES this product should work. We can only confirm with certainty that it is compatible with any Quick Mill, Izzo and Rocket machine being that those are the machines we stock and sell here. However it should also work on any Expobar, Bezzera, ECM or Profitec machines as well. Please read our returns \u0026amp; exchanges policy before ordering. \u003c\/p\u003e\n\u003ch3 data-mce-fragment=\"1\"\u003eCompatible with the Following Machines\u003c\/h3\u003e\n\u003ch3 data-mce-fragment=\"1\"\u003eIzzo\u003c\/h3\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003eDuetto \u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003eDuetto Evo\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003eVivi PID\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3 data-mce-fragment=\"1\"\u003eQuick Mill\u003c\/h3\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003eAlexia\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003eCarola\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003eAnita\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003eAndreja Premium\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003eQM67\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003eVetrano 2B\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3 data-mce-fragment=\"1\"\u003eRocket\u003c\/h3\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003eAppartmento\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003eR58 Cinquantotto \u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003eMozzafiato - both models\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003eGiotto - both models\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp data-mce-fragment=\"1\"\u003e Isomac, Expobar and ECM, as long as they have an E61 group, will also be compatible. \u003c\/p\u003e\n\u003ch3 data-mce-fragment=\"1\"\u003e\u003cb data-mce-fragment=\"1\"\u003eManual Flow Profiling\u003c\/b\u003e\u003c\/h3\u003e\n\u003cp data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e\u003cmeta charset=\"utf-8\"\u003e \u003cspan style=\"text-decoration: underline;\"\u003e\u003ca data-mce-fragment=\"1\" title=\"quick mill e61 flow control mushroom installation manual\" href=\"https:\/\/shopify-er.s3.amazonaws.com\/resources\/4623197306916\/manual.pdf\" target=\"_blank\" data-mce-href=\"https:\/\/shopify-er.s3.amazonaws.com\/resources\/4623197306916\/manual.pdf\"\u003e\u003cstrong data-mce-fragment=\"1\"\u003eInstallation Manual\u003c\/strong\u003e\u003c\/a\u003e\u003c\/span\u003e\u003c\/span\u003e\u003c\/p\u003e\n\u003cp data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eWith the Quick Mill E61 group head flow control device you can manually profile your extractions by adjusting the flow from the closed position (0-bar) to full pump pressure, usually 9-bar. This E61 flow control device can work on many common machines like the ECM flow control device does.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eThe flow control device can be installed in machines that are equipped with standard E61 groupheads. With just a couple of tools, your coffee machine will be able to vary the amount of flow using the stainless steel needle valve now installed on your E61 group. This needle valve is the main working component that allows the user to vary the flow of water to your coffee where you’ll have full control of saturation and extraction of all that you love about your espresso!\u003c\/span\u003e\u003c\/p\u003e\n\u003cp data-mce-fragment=\"1\"\u003e\u003cmeta charset=\"utf-8\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eThe Flow Control Kit replaces the E61 spring with a stiffer one that does not compress unless manually activated to drain excess pressure through the exhaust. This is so that you do not have to manually manage the pressure of controlling the flow restriction while simultaneously compensating for the pressure difference as that pre-infusion valve compresses.\u003c\/span\u003e\u003c\/p\u003e\n\u003ch3 data-mce-fragment=\"1\"\u003e\u003cb data-mce-fragment=\"1\"\u003eInstalling the E61 Flow Control\u003c\/b\u003e\u003c\/h3\u003e\n\u003cp data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eThe Quick Mill flow control kit provides you with all of the necessary pieces you’ll need to install it to your existing E61 group. It installs on the front of the group with just a couple of tools required:\u003c\/span\u003e\u003c\/p\u003e\n\u003cul data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eTeflon Tape\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eElectrical Tape\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e5mm Allen Key\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003e12” Adjustable Socket Wrench\u003c\/span\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp data-mce-fragment=\"1\"\u003e\u003cmeta charset=\"utf-8\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eWhen installing your new gauge, we recommend that you very gently screw in the gauge just until it is barely finger tight. Then unscrew it until the gauge is upright. Then unscrew it, counting the number of rotations you go through. From there, wrap the male threads of the gauge with teflon tape and tighten it back in that same number of turns. That way it will both be in the position you want, and also seal so that it does not leak.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eIf you have any questions or concerns, please do not hesitate to call or email our service technicians during business hours (Monday-Friday 8am-5pm EST) at 518-452-5995 or email \u003cspan style=\"text-decoration: underline;\"\u003e\u003ca href=\"mailto:support@chriscoffee.mom\"\u003esupport@chriscoffee.mom\u003c\/a\u003e\u003c\/span\u003e.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp data-mce-fragment=\"1\"\u003e \u003c\/p\u003e\n\u003ch3 data-mce-fragment=\"1\"\u003e\u003cb data-mce-fragment=\"1\"\u003eOnce You've Gathered all Necessary Tools Required for Installation, Follow These Easy Steps.\u003c\/b\u003e\u003c\/h3\u003e\n\u003col data-mce-fragment=\"1\"\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eWrap the top of the mushroom with electrical tape to prevent it from getting marred by the 12” adjustable socket wrench.\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eLoosen the mushroom at the top of the group with the adjustable wrench.\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eRemove the mushroom from the top of the group, along with the Teflon seal and set aside.\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eGrab the new mushroom that came with the Quick Mill E61 flow control kit and unscrew the black knob. Now remove the knob and cap before inserting the mushroom into the top of the group.\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eReplace the Teflon seal that was removed in step three with the new seal that was included with your flow control kit. Install the new mushroom and tighten.\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eWith your hand, turn the post that has been exposed after removing the black knob and cap clockwise until hand tight. This is ensuring that the needle valve is completely closed in this position or ‘off’ as we’ll refer to it.\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eNow that the valve is in the closed position, set the cap with the black knob attached back on the post you just tightened. Once placed on the post tighten the black knob. This will maintain the position of the cap so as you start to adjust flow the cap does not move positions.\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eWith the 5mm Allen wrench unscrew the Allen screw on the front-center of your E61 group.\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eRemove the Teflon seal and install it on the backside of the gauge.\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eWrap Teflon tape around the threads below the Teflon seal a couple of times and finger tighten the pressure gauge on the front of the group to lock it into place.\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eWrap electrical tape around your discharge spout and loosen the nut closest to the top of the spout until removed.\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\u003cspan data-mce-fragment=\"1\"\u003eOnce the discharge spout has been removed, remove the pre-infusion valve. Replace the brew valve spring that surrounds the pre-infusion valve with the spring that was included in the E61 Group Head Flow Control Device Kit.\u003c\/span\u003e\u003c\/li\u003e\n\u003cli data-mce-fragment=\"1\"\u003e\n\u003cspan data-mce-fragment=\"1\"\u003eOnce the brew valve spring has been replaced around the pre-infusion valve and inserted back into the discharge spout, tighten the discharge spout back into the bottom of your E61 group, and you’re ready to start up your espresso machine!\u003c\/span\u003e \u003c\/li\u003e\n\u003c\/ol\u003e","brand":"Quick Mill","offers":[{"title":"Default Title","offer_id":40311438147620,"sku":"KIT0995RFLC-LE","price":245.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0079\/0665\/6292\/products\/flow-control-wood.jpg?v=1667845236","url":"https:\/\/www.chriscoffee.mom\/products\/quick-mill-flow-control-lever-wood","provider":"Chris' Coffee","version":"1.0","type":"link"}